Search found 2013 matches

by Growlerbearnz
Thu Nov 14, 2019 1:41 pm
Forum: L300 Technical
Topic: Hand throttle - open or closed when off
Replies: 1
Views: 2678

Hand throttle - open or closed when off

On a diesel? The idle speed knob to the left of the steering column? It makes no difference. All it does is hold the accelerator pedal down a little. Generally you're only supposed to use it when the engine's cold, to increase the idle speed. Once the engine's warm it should idle at 750rpm without u...
by Growlerbearnz
Thu Oct 31, 2019 3:11 pm
Forum: General Discussion
Topic: 1993 L300 Pre-Purchase Inspection HELP
Replies: 3
Views: 4114

1993 L300 Pre-Purchase Inspection HELP

A 4D56 should idle at 750rpm. There's an idle increase knob beside the steering column- twist it to unlock, to make sure it's not just stuck on. The main thing to look out for is rust in the A-pillar, windscreen surround, and roof- especially around a sunroof/crystal lite glass. If there's rust in t...
by Growlerbearnz
Tue Oct 22, 2019 1:52 pm
Forum: General Discussion
Topic: Need help referencing and locating parts
Replies: 6
Views: 5920

Need help referencing and locating parts

Check out the FAQ, lots of resources in there http://www.delica.ca/forum/viewforum.php?f=16

There's an excellent post on finding part numbers: http://www.delica.ca/forum/viewtopic.php?f=16&t=17210.
by Growlerbearnz
Sat Oct 19, 2019 2:20 pm
Forum: General Discussion
Topic: ReCasting Bushings with Polyurethane
Replies: 12
Views: 10288

ReCasting Bushings with Polyurethane

Go for it! I'd use plastic instead of cardboard, or wax/grease the cardboard so it releases cleanly. Did you notice how he very carefully never showed the back side of any of the bushes? I bet they're a mess of ugly stuck-on cardboard. :-) My only concern would be that they might end up transmitting...
by Growlerbearnz
Tue Oct 15, 2019 10:12 pm
Forum: L300 Technical
Topic: Coolant dripping near oil filter
Replies: 2
Views: 2971

Coolant dripping near oil filter

Assuming you've ruled out the obvious sources (tired radiator hoses, head gasket leak, thermostat housing) the usual suspect is the heater pipe-to-water pump O-ring. Between the exhaust manifold and the block you'll find a steel pipe which runs around the back of the block to the heater hoses. That ...
by Growlerbearnz
Sat Oct 05, 2019 8:32 pm
Forum: L300 Technical
Topic: How to dismantle sliding windows?
Replies: 3
Views: 3745

How to dismantle sliding windows?

I posted about this over on DelicaForum just the other day! http://delicaforum.com/index.php?thread ... ment.1478/
by Growlerbearnz
Fri Oct 04, 2019 2:54 pm
Forum: Member Introductions
Topic: Hopefully a Delica owner by next week
Replies: 2
Views: 3957

Hopefully a Delica owner by next week

Fuel economy on the 3l V6 isn't great, 16-20mpg (about 13l/100km). It's a very heavy van with the aerodynamics of a brick.
by Growlerbearnz
Fri Sep 27, 2019 2:45 pm
Forum: General Discussion
Topic: Windshields Available in Calgary
Replies: 13
Views: 9081

Windshields Available in Calgary

Front and rear windscreens are all the same whether high- or low-roof. The US market* Mitsubishi Van and Wagon use the same glass, so that might give you some other options.

*Yes I know Canada isn't the USA. Sorry.
by Growlerbearnz
Tue Sep 24, 2019 9:37 pm
Forum: L300 Technical
Topic: Starter Motor Issues
Replies: 6
Views: 5500

Starter Motor Issues

Hah! the pinhole leak is a classic. I had an MG that ran fine until it got hot, then started misfiring until it stopped. Clearly an electrical/spark misfire. Replaced the coil and condenser (they can fail when hot). Replaced the distributor cap, rotor, and leads. Spark plugs. Points. Checked all the...
by Growlerbearnz
Mon Sep 23, 2019 11:39 pm
Forum: L300 Technical
Topic: Starter Motor Issues
Replies: 6
Views: 5500

Starter Motor Issues

Before you go spending all the moneys, try a couple of tests for me? l300_12v_egr_hyundai_mitsubishi_starter_motor_m2t56181_js344_16853_1_year.jpg Make sure it's in neutral. Using one side of a pair of jumper leads, apply 12V to the small spade terminal (A, red) If the starter runs, you have a wirin...
by Growlerbearnz
Thu Sep 12, 2019 7:03 pm
Forum: L300 Technical
Topic: L300 Automatic and Manual = same engine?
Replies: 3
Views: 3468

L300 Automatic and Manual = same engine?

^What he said. All same, though you'll have to swap a few minor things from one engine to the other depending on which direction you're going. Flywheel/flex plate, kickdown linkage, ... err... I think that's it actually!
by Growlerbearnz
Tue Aug 27, 2019 9:12 pm
Forum: L300 Technical
Topic: Leaking Fuel Tank
Replies: 7
Views: 5280

Leaking Fuel Tank

Yup, that Ebay tank is the rear tank :-(
by Growlerbearnz
Mon Aug 26, 2019 6:43 pm
Forum: L300 Technical
Topic: Glow Plug/Starter Issue for a Newbie
Replies: 5
Views: 5336

Glow Plug/Starter Issue for a Newbie

The ignition lock is probably easy- the switch on the back of the lock can just fall out. Remove the steering column trim and I bet you'll find the electrical part of the ignition barrel is dangling. The usual fault is the black contacts section comes unclipped and falls out- you can usually just cl...
by Growlerbearnz
Mon Aug 26, 2019 6:38 pm
Forum: L300 Technical
Topic: Leaking Fuel Tank
Replies: 7
Views: 5280

Leaking Fuel Tank

The two tanks are completely different shapes, and have different connections. The front tank is rectangular, the rear tank is squarer but deeply scalloped to avoid the driveshaft. http://www.delica.ca/forum/viewtopic.php?f=91&t=17225 ...I'm guessing you haven't tried sticking your head under th...
by Growlerbearnz
Mon Aug 26, 2019 1:43 pm
Forum: L300 Technical
Topic: Leaking Fuel Tank
Replies: 7
Views: 5280

Leaking Fuel Tank

I swear by POR15 Fuel Tank Sealer, as long as you follow the instructions . ( https://www.por15.com/POR-15-Fuel-Tank-Sealer ). You also need Cleaner/Degreaser ( https://www.por15.com/POR-15-Cleaner-Degreaser ) and Metal Prep ( https://www.por15.com/POR-15-Metal-Prep ). When I added the extended fuel...

Go to advanced search