Delica Canada | Mitsubishi Van Club

Hello you Canadians... I am having some trouble finding parts online for my Delica and since CVI is across the boarder from me it makes it somewhat difficult to find the stuff I want. Any websites that have aftermarket parts?

I am looking for a beefier bull bar or front push bar like the one in some of the youtube videos like this one http://www.youtube.com/watch?v=vVBHTRMjNs8

I would ideally like this guys whole set up for bars, im trying to make mine into a hamster ball for the zombie apocalypse. Any direction or websites for parts is much appreciated. BTW I have a 1989 Delica L300 and it IS state side, fully registered and insured.. so giddy up nay sayers!

For a rear swing away tire carrier, i believe that someone on here modded up a trailgear tube bumper for a jeep wrangler. the brackets had to be extended into the unibody etc, but after all was said and done it looked slick. The vast majority of parts like armor will be pretty much impossible to find for your van. all of the stuff is custom jobs. So with enough thinking and backyard engineering, you can come up with pretty much anything. As far as the front end, you are going to have to extend where the OEM bumper connects to whatever else you are trying to bolt on.

Hope this helps!

sub-arctic wrote:For a rear swing away tire carrier, i believe that someone on here modded up a trailgear tube bumper for a jeep wrangler. the brackets had to be extended into the unibody etc, but after all was said and done it looked slick. The vast majority of parts like armor will be pretty much impossible to find for your van. all of the stuff is custom jobs. So with enough thinking and backyard engineering, you can come up with pretty much anything. As far as the front end, you are going to have to extend where the OEM bumper connects to whatever else you are trying to bolt on.

Hope this helps!

Hi, Im one of the guys that did the rear swing tire carrier mod, I did consider doing the same for the front, as a rock crawler front bumper is readily available as well. The "mod" is actually considerably easier for the front as the frame rail is more accessable to mount.(existing tabs are there) I decided against it as I felt I had enough wind drag, but mostly because the weight over the front is too biased already. An L300 can benefit from added rear weight, but definately NOT the front. The approach angle is also an issue on the L300, so if I were to do it I would certainly go compact. Just my 2c.

Seen this?

http://www.delica.ca/forum/l300-bullbar-swap-13307.html

yojimbo wrote:Seen this?

http://www.delica.ca/forum/l300-bullbar-swap-13307.html

Look who the second poster from the bottom is.

nxski wrote:

yojimbo wrote:Seen this?

http://www.delica.ca/forum/l300-bullbar-swap-13307.html

Look who the second poster from the bottom is.

Yeah its me, no wait when I post this, its you.

Dont blame me, its nearly 11pm here in the UK, and I have consumed alcomohol.

Beer excuse for the win!

yojimbo wrote:Beer excuse for the win!

That post should be in the "who is DRUNK posting?" thread.

nxski wrote:

yojimbo wrote:Beer excuse for the win!

That post should be in the "who is DRUNK posting?" thread.

Lets not be premature, I'm still drinking!

YES, that gnarly bumper is the one im looking for. What is that off of and how can i get it mounted... thank you everyone for the responses. I am looking for "armor" style bumpers everywhere which is the look and durability im going for.

WS Skoo B wrote:YES, that gnarly bumper is the one im looking for. What is that off of and how can i get it mounted... thank you everyone for the responses. I am looking for "armor" style bumpers everywhere which is the look and durability im going for.

Such information is secretly stored in the words of the thread. Hold the thread over an open flame to reveal its cunning secrets:

gezzza wrote:Any body looking to upgrade the old possum bar i found a 60 series landcruiser bar will fit nicely.

^^^^ hahaha verrry funny, yea I re-read the post and saw that. I was hoping to try to get one mounted without too many mods, do you think there is a way to bolt it on without extending my frame rails?

and I appreciate everyones help this Forum is the only resource I have for this awesome vehicle.

Simply adapt to the stock Bushbar mounting tabs..