Air adjustable shock absorbers

Mitsubishi Delica Camper vans, lift kits & other Delica Accessories!

Moderator: BCDelica

User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Air adjustable shock absorbers

Post by Growlerbearnz »

Ouch! So the pin sheared off? At the base (where it meets the shock) or at the threads? The shocks need to tilt on the lower mounts as the suspension goes up and down, so I guess overtightening the pin would reduce the amount of flex in the bushes.

The strength of the shock mounts *is* potentially an issue- air shocks have a reputation for breaking mounts on regular cars. Anecdotally it happens when they're used to lift the suspension rather than just to compensate for extra load, but they do put extra stress on the mounts.

I figure our shock mounts can probably handle it- the upper mounts are common to all L300s, including the long-wheelbase 4WD commercial vans which are rated to take far more load than ours. L300s are abused as delivery vans here, and they don't have a reputation for the shock mounts breaking- and I don't think the air shocks add *that* much extra load.

But I might have just invoked Murphy's Law on myself...
Nothing says "poor workmanship" more than wrinkles in the duct tape.
sk66
Posts: 189
Joined: Thu Oct 06, 2016 3:24 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '91 Delica L300
Location: Pennsylvania, USA

Air adjustable shock absorbers

Post by sk66 »

:-D
At the base where it meets the shock... looks like it was a questionable weld as well.
Steven
1991 L300
Harrisburg, PA
User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Air adjustable shock absorbers

Post by Growlerbearnz »

Hmm. Dodgy. Will you try for a warranty claim?
Nothing says "poor workmanship" more than wrinkles in the duct tape.
sk66
Posts: 189
Joined: Thu Oct 06, 2016 3:24 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '91 Delica L300
Location: Pennsylvania, USA

Air adjustable shock absorbers

Post by sk66 »

I just bought another set... the cost is pretty low and I figured the hassles of shipping and fighting over modification/unintended application are probably not worth it.
But the weld broke very cleanly w/ the appearance of not much penetration... I definitely suspect it was at least a contributing factor. I might send a letter/pic just to see what they say.
Steven
1991 L300
Harrisburg, PA
User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Air adjustable shock absorbers

Post by Growlerbearnz »

You mentioned that overtightening the pin might not have helped. On mine the lower nuts are tightened so there are about 2 threads exposed beyond the nut. Mine came with regular nuts (not nylocs) so I used some thread lock.
ShockLower.jpg
ShockLower.jpg (330.71 KiB) Viewed 21638 times
Note that the upper bush is more compressed than when first installed: when I installed them, both rubber bushes were under similar tension, but once I put 40psi into the shocks the extra pressure compressed the upper bush a bit more, and let the lower bush relax (but the lower cupped washer isn't loose).
Nothing says "poor workmanship" more than wrinkles in the duct tape.
User avatar
joebillhill
Posts: 163
Joined: Wed Apr 02, 2014 10:52 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 Mitsubishi Delica l300
Location: United States

Air adjustable shock absorbers

Post by joebillhill »

Man those pins are a pain to get out! I ended up hack sawing off both ends then using sockets to be able to push the remaining metal out for anyone looking for a different way/ only has access to a C clamp..
User avatar
Growlerbearnz
Posts: 2041
Joined: Sat Jun 26, 2010 1:58 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Delica P25W
Location: New Zealand

Air adjustable shock absorbers

Post by Growlerbearnz »

joebillhill wrote:Man those pins are a pain to get out!
Indeed. You could almost say "
Growlerbearnz wrote:it's more difficult than it looks
;-)
Nothing says "poor workmanship" more than wrinkles in the duct tape.
User avatar
joebillhill
Posts: 163
Joined: Wed Apr 02, 2014 10:52 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1989 Mitsubishi Delica l300
Location: United States

Air adjustable shock absorbers

Post by joebillhill »

Oh I'm in total agreeance Growler. I'm just saying for those without a vise or zen-like patience there is the hacksaw :twisted:
sk66
Posts: 189
Joined: Thu Oct 06, 2016 3:24 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '91 Delica L300
Location: Pennsylvania, USA

Air adjustable shock absorbers

Post by sk66 »

joebillhill wrote: Wed Oct 17, 2018 8:53 am Man those pins are a pain to get out! I ended up hack sawing off both ends then using sockets to be able to push the remaining metal out for anyone looking for a different way/ only has access to a C clamp..
When I did the replacement shock I just cut off one side of the pin and used a gear puller to push the rest through. I have a few different ones, but even a small/cheap one (~$10) should be able to do the job. It was muuuch easier than wresting with the vise (I also used a cutoff disk/grinder).
Steven
1991 L300
Harrisburg, PA
User avatar
lrp374
Posts: 1023
Joined: Sun Nov 23, 2008 9:56 pm
Vehicle: 91 Super Exceed
Location: Kamloops

Air adjustable shock absorbers

Post by lrp374 »

I just found out Rock Auto has these and I ordered a pair shipped to Kamloops for $112 CAD including duty, which I'm really happy about. Even supposed to be here before Xmas.
User avatar
lrp374
Posts: 1023
Joined: Sun Nov 23, 2008 9:56 pm
Vehicle: 91 Super Exceed
Location: Kamloops

Re: Air adjustable shock absorbers

Post by lrp374 »

I discovered this week that my air shocks have failed. I installed them in March and only have a few thousand km on them. The top broke off which is the opposite end to sk66. I'm not sure how they welded it together but if that's all that's holding then it's no wonder they don't last long. Rather than by more I decided that nothing is lost to try and weld them and so far they work fine. We'll see after they spend some time on corduroy back roads. I've attached a couple of pictures so you can see the original 'weld'.
Attachments
100_9742a.JPG
100_9742a.JPG (118.11 KiB) Viewed 17740 times
100_9740a.JPG
100_9740a.JPG (61.29 KiB) Viewed 17740 times
User avatar
lrp374
Posts: 1023
Joined: Sun Nov 23, 2008 9:56 pm
Vehicle: 91 Super Exceed
Location: Kamloops

Re: Air adjustable shock absorbers

Post by lrp374 »

Well the other shock broke @ the top on the weekend exactly the same as the first one. I could have taken another picture and it would have been exactly the same. The good news is the first one is still holding and I've welded this one so I have 2 'good' shocks again. See how long they stay in one piece this time.
Post Reply

Return to “Delica Modifications”