in need of delica parts? enter here!

Looking for a specific hard-to-find Delica part? Post your request in this section. Commercial postings can be found in "Delica Trader Parts Section".

Moderators: delicanuck, mark

Post Reply
kris85
Posts: 8
Joined: Fri Mar 26, 2010 6:56 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1st Generation Mitsubishi Lancer

in need of delica parts? enter here!

Post by kris85 »

good day everyone! i am kris from the philippines and i recently joined the forum. we have tons of delicas here in our country and i usually see one being parted out in a junk shop. if anyone needs a delica part or two, feel free to post the part you need here so that i can give you a quote as to how much it will cost you for the part and its shipping. i go to the junk shop to salvage parts at least once a week (during my rest days from my job). thanks and godbless.
fmande
Posts: 155
Joined: Fri Apr 16, 2010 5:12 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 97 TD exceed SWB
Location: Mount Compass S.Aus

Re: in need of delica parts? enter here!

Post by fmande »

G'day mate I see you made it,

good luck with it.

regards fmande
regards David


The more you learn the less you know.
By the time I die I will know absolutely nothing.
kris85
Posts: 8
Joined: Fri Mar 26, 2010 6:56 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1st Generation Mitsubishi Lancer

Re: in need of delica parts? enter here!

Post by kris85 »

yep! actually registered to this forum a few days ago... hehehe...
Greeny007
Posts: 1
Joined: Sun Apr 11, 2010 3:06 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: Mitsubishi Delica l300

Re: in need of delica parts? enter here!

Post by Greeny007 »

Hello, can you get a rear tail light for a 1992 l300?
fexlboi
Posts: 1671
Joined: Thu Jun 19, 2008 11:28 pm
Member's Photo Album: http://dinoevo.de
Vehicle: -
Location: -
Contact:

Re: in need of delica parts? enter here!

Post by fexlboi »

Looking for a window switch for a 94' l300
http://dinoevo.de/wp-content/gallery/re ... g_0906.jpg
twisted
Posts: 67
Joined: Mon Apr 14, 2008 6:49 pm
Vehicle: 92 Super Exceed
Location: Edmonton AB

Re: in need of delica parts? enter here!

Post by twisted »

Hey what kind of price for a turbo? 92 l300.
Meanman
Posts: 342
Joined: Sun Dec 07, 2008 5:27 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 1990 Exceed Crystal lite
Location: Maple Ridge

Re: in need of delica parts? enter here!

Post by Meanman »

Air conditioning compressor for L300, Relay/solenoid for crystal light roof shades.
YOUTH JUICE YOUTH JUICE RESTOR
The Goodness of 7 Pounds of Whole Berries+ 3 Sea Vegetables in Every Bottle
http://www.jhallen.youthjuice.com
User avatar
jwfchase
Posts: 508
Joined: Mon Dec 03, 2007 10:36 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '92 Super Exceed
Location: Kamloops, BC

Re: in need of delica parts? enter here!

Post by jwfchase »

Pre- 1991 sliding window (not the pop-out kind) for L300
erik2287
Posts: 14
Joined: Thu Jun 10, 2010 10:23 pm
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: 92 Delica Exceed
Location: Van City
Location: Vancouver, BC

HELP

Post by erik2287 »

Hi,

I have a 1992 Delica Super Exceed and need an English manual as my Japanese is a little rusty.

Any suggestions?

Thanks

Erik in Vancouver
SSB
Posts: 7
Joined: Fri Feb 19, 2010 12:25 am
Member's Photo Album: http://www.delica.ca/Photos/
Vehicle: '95 Spacegear

Re: in need of delica parts? enter here!

Post by SSB »

Can you get your hands on some fender flares aka wheel arches for a '95 L400? Thanks!
RichD
Posts: 948
Joined: Mon Apr 19, 2010 6:05 pm

Re: HELP

Post by RichD »

erik2287 wrote:Hi,

I have a 1992 Delica Super Exceed and need an English manual as my Japanese is a little rusty.

Any suggestions?

Thanks

Erik in Vancouver
I can help you out with that here in Vancouver area. I have digital service manuals (almost if not all are in the wiki section for download) as well as a translated user manual and service manual which I'm working on digitizing. Cost: zero!

I had mine printed and bound at a local print shop for a few bucks.
Richard Dagenais
Post Reply

Return to “Parts Wanted (Non-Commercial)”