Delica Canada | Mitsubishi Van Club

I live in Calgary and i have a oil pan heater,block heater and run synthetic oil. If you run 15/40 you could blow a head gasket. Even if you just have a block heater, that is good. Heat you oil

I have noticed when i do let it idle at low RPM it is cold ( low temp not very warm ) at any length of time. I do let it get to a smooth idle before i drive and oil pressure gets down. I do this because i was told by the fellow who fixed my diesel rabbit to much pressure on a cold day will find the ...

I have installed a oil gauge to see what my old 89 pj was doing. On a cold day in calgary the oil gauge is up to 90 to 100, cold start not plugged in -10 ish. I let it warm up until the oil gauge hit 60 ish. This takes about 5 min. I only do this so i don't blow my head gasket. This is what i am to ...

I did put .25 gas in my 89 pj. It turns out to be 75% diesel 25% gas. Ran like crap. Drove 100k put more diesel in did that 3 times. All was fine. But I did not drive it hard at all. I have in the past put gas in my old vw diesel but only 1/3 and vw operator manual was fine with that. Drain tank as ...

I headed out west and hit the island. I so far have gone up and down the coast and not a wave from any L300 Or any L400 Guess they don't see a 1989 pajero much. I am happy just the same being here. The boost on my turbo was turned up from 8lbs to 12lbs and performed quite well from Calgary to Van Is...

cant do it on the 18 or 19 but the 25 is a great day for me to make it out. Working on Sundays new shift burns.

From what i can tell from the posts your sending unit is working and your gauge is working. The only problem now is the float attached to the sending unit solid or hallow , if it is hallow it has cracked and fuel has got inside it there for weighing it down. That is one of the things that can set th...

1983 Dodge D50 ram royal in pick and pull. The trans and transfer case still in it. The motor was gone. Plate on fire wall said it had a 4d55 in it. Calgary ab. Might work it is standard not sure though if it is an exact match

Well i made it through winter and the spring with my wipers not acting up. So i have redone them and lubed them with chain lube, all the joints where lubed, and drilled holes in the rotating parts and lubed that. It now works great in the rain.

It's not the motor. It's the wiper arm assembly. You need to remove it and drill into the part that houses the rotating part. Drill just deep and wide enough to put the plastic spay tip from a wd40 nozzle. But use chain lube. This is a common thing in the imports. Water gets behind the wipers and co...

For the last week and a half i had this annoying rattle in the front wheel. This is what i found. photo[1].JPG photo[2].JPG I did try Canadian Tire because the have a sale buy one get next 1/2 off. But as most of you know there is no help there unless u have a Canadian Tire code. I asked for them to...

Got my 89 pj at 175000ks. Done the timing,glow plugs, block heater,heater fan,belts ,brakes,ac dryer,recharge ac,trans filter and diff/transfer case oil changed $2500 in all so far. Why for such a old suv because this diesel motor will run for a long time. And is still in my mind one hell of a wicke...

This is the begining of the end. The smell is correct. That is what I went through with my 89 pajero. The smell then the drip , the coolant level did not go down at first but over time is did very little at a time. Spent a day taking the dash out, and the heater core. When I looked at the core it tu...

I will try to be down with that. APR 9,16 I am out but free 23 30. Wed's no prob this time, to go to peters. Keep me posted.

It turns out i have the older version of your newer rides so i cant use the 92 montero rear pads. the design changed in 90 11 yy mm. Sucks for me. Here is what i have found out for my rear pads . Cross ref brand and # AKEBONO A-200K AKEBONO AN-200K FBL AFP152 KASHIYAMA D6013 MITSUBISHI MB407390 MITS...